Channel Scanning Instructions

New Channels Available

Rescan for 3ABN, 3ABN Latino Radio, and 3ABN Proclaim Networks


Good news! 3ABN has made two new channels available on your G-19 satellite system. Now you can watch the Dare to Dream television network, and listen to the new 3ABN Latino Radio (Spanish) network.

To accommodate these new choices, 3ABN’s Proclaim channel has been moved to a new frequency, and you will need to rescan your channels to receive it.

If you have a current Glorystar receiver, you will receive an automatic update over the air, but if you have an older receiver (Manhattan, Topfield, or Fortec Star), you will need to rescan your channels.

Below you will find a list of each receiver. Just click on the link, and you will be redirected to step-by-step instructions for your receiver. The best method for updating your set-top box to receive all the Adventist channels is to delete your current programming, scan for the new channels, and delete any unwanted channels.

BEC 1000 / 2000″ variation
1. Place the BEC 1000 / 2000 satellite receiver on Channel 1
2. Using the remote control press the “MENU” button to display the “Channel List” screen
3. Press Right Arrow button to display “Channel Edit” screen with the TV icon highlighted
4. Press Enter button to display the “TV CH Edit” screen
5. Press Enter button to place a “X” to the left of the channel name
6. Press Down Arrow button to highlight the next channel name
7. Press Enter button to place a “X” to the left of the channel name
8. Repeat steps 6 and 7 until all channels have a “X” beside the channel name
9. Press Menu button to display a pop up window
10. Press Down Arrow 2 times to highlight “Delete”
11. Press Enter button
12. Press Return button to display the “Channel Edit” screen
13. Press Right Arrow button to display “Setup” screen with “CH Search” highlighted
14. Press Enter button to display “Channel Search” screen with “Satellite” highlighted
15. Press Down Arrow button to highlight “Frequency”
16. Using the numeric keypad, enter 11842
17. Press Down Arrow button to highlight “Symbol Rate”
18. Using the numeric keypad, enter 22000
19. Press Down Arrow button to highlight “Polarization”
20. Press Enter button to select “Horizontal”
21. Press Down Arrow button to “Scan”
22. Press Enter button to scan for new channels. When the scan is completed a popup window appears ” Scan Message: Scan Complete”
23. Press the Return button to enter Channel Search screen.
24. Press Down Arrow button to highlight “Frequency”
25. Using the numeric keypad, enter 12060
26. Press Down Arrow button to highlight “Symbol Rate”
27. Using the numeric keypad, enter 22000
28. Press Down Arrow button to highlight “Polarization”
29. Press Enter button to select “Horizontal”
30. Press Down Arrow button to “Scan”
31. Press Enter button to scan for new channels. When the scan is completed a popup window appears ” Scan Message: Scan Complete”
32. Press Return button 3 times to display a popup window “Confirm Save” with “OK” highlighted
33. Press Enter button. The receiver will restart and the new channels will be added to your channel list. Please note that the satellite name will be displayed as AMC4, but it really has been changed to the new satellite Galaxy 19. 


To Remove Unwanted Channels
34. press the “MENU” button to display the “Channel List” screen
35. Press Right Arrow button to display “Channel Edit” screen with the TV icon highlighted
34. Press Enter button to display the “TV CH Edit” screen
35. Press up or down button to highlight the unwanted channel
36. Press Enter button to place a “X” to the left of the channel name
37. Continue going down the list and mark all unwanted channels with an “X” besides them
38. Press Menu button to display a pop up window
39. Press Down Arrow 2 times to highlight “Delete”
40. Press Enter button to delete
41. Press Return button twice, the prompt will show Confirm Save: Save Change To Database?
42. Press Enter to confirm, pop up window will show Confirm Save Information: Please Wait, Saving Data
43. View programming

Fortec Star Mercury II
1. Using your Fortec Star Mercury II remote control press “Menu” button to go to “Installation” screen
2. Press the Channel down button to highlight “Factory Reset”
3. Press OK button to go to “Factory Reset” screen with Factory Reset line highlighted
4. Press OK button. A pop up window displaying “Are You Sure?” with “No” highlighted yellow
5. Press VOL down button to highlight “Yes” with yellow
6. Press OK button
7. When Language screen appears, turn off master power switch on back of receiver or unplug receiver from AC power outlet for 10 seconds
8. Turn the receiver back on or plug the receiver back into AC power outlet. “Language” Menu will appear
9. Press “Menu” to go to “Installation” screen with “Antenna Setup” highlighted
10. Press OK button to enter “Antenna Setup” screen
11. If needed, press VOL down button (the button that points left) to select “Galaxy25 Ku 97.0W or IA5/KU 97.0W”
12. Press the Channel down button to highlight “LNB TYPE”
13. Press VOL up button to display “LNB-10750”
14. Press the Channel down button to highlight “0/22kHz” line and press the VOL up right arrow button to display On
15. Press the Channel down button to highlight “Switch” line and press the VOL up right arrow button to display DiSEqC 1.0
16. Press the Channel down button to highlight “Input” line and press the VOL up right arrow button to display LNB 2
17. Press Menu button to go back to “INSTALLATION” screen, prompt will display “Saving”
18. Press the Channel down button twice to highlight “TP SCAN”
19. Press OK button to go to “TP SCAN” screen
20. Press the Channel down button to highlight “FREQUENCY”
21. Using the numbers buttons on the remote control enter 11842
22. Press Channel down button to highlight “POLARITY” and push the Volume up button (the button that points to the right) it should display “Horizontal”
23. Press Channel down to “SYMBOLRATE”
24. With the number buttons on the remote control enter the numbers 22000
25. Press Channel down to “Save Edit” line and press OK to store. Store prompt will show for a moment
25. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY”
26. If you have the “Signal Quality” bar with the highest strength (at least 50%), press Yellow button
27. When Channel Scan is completed, pop up window displaying “Do you want to save?” with “Yes” highlighted yellow
28. Press OK button to save. Programming will automatically be displayed
29. Press Menu button to enter “INSTALLATION” screen
30. Press the Channel up or down to highlight “TP SCAN”
31. Press OK button to go to “TP SCAN” screen
32. Press the Channel down button to highlight “FREQUENCY”
33. Using the numbers buttons on the remote control enter 12060
34. Press Channel down button to highlight “POLARITY” and if necessary push the Volume up button (the button that points to the right) it should display “Horizontal”
35. Press Channel down to “SYMBOLRATE”
36. With the number buttons on the remote control enter the numbers 22000 if necessary
37. Press Channel down to “Save Edit” line and press OK to store. Store prompt will show for a moment.
38. On the bottom of the screen you will see two bars, one says “SIGNAL LEVEL” and the other “SIGNAL QUALITY”.
39. Verify the “Signal Quality” bar with the highest strength of at least 50% or better. If not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel.
40. Press Yellow button to scan new channels
41. When Channel Scan is completed, pop up window displaying “Do you want to save?” with “Yes” highlighted yellow
42. Press OK button to save. Programming will automatically be displayed

Optional Steps: If you would like to view all available free programming from this satellite (this will include secular and international programming) 
There are approximately 200 TV stations and 100 Radio stations on this satellite
43. Press P.SCAN button under blue Timer button
44. Press Channel up button to “Mode” line and push the Volume up button to display Scan FTA
45. Press Channel down button to Starn Scan line and press the OK button
46. POWER scan screen will appear and will list all available services on the satellite. Do not interrupt, this process may take up to ten minutes to complete
47. The prompt will show “Do you want to save?” with Yes highlighted yellow
48. Press the OK button to save. Prompt “Saving’ will show and Power Scan screen will display. Press exit to view programming

Deleting unwanted channels:
49. Press Ok/List button
50. Press the Blue button to Edit the channel list
51. Press the Channel down button to highlight Delete Channel
52. Press the OK button, a small gray button will appear next to each channel name
53. Use the Channel up and down button to highlight channel to be deleted
54. Press the OK button to mark the channel for deletion, the button will turn red
55. Repeat steps 53 and 54 until all unwanted channels are selected
56. Press the Blue button to DELETE, a prompt will display “Do you want to save?” use Vol down left arrow to select Yes highlighted yellow
57. Press the OK button, saving prompt will appear
58. Press exit to view programming

Fortec Star Lifetime Ultra
1. Using your  Fortec Star Lifetime Ultra remote control push “Menu” button
2. Press left arrow button to select System Setup menu screen
3. Press down arrow to select Factory Setting
4. Press the OK button
5. Prompt will request a password, enter 0000, prompt will ask for OK button to delete
6. Press the OK button, the receiver will restart
7. Press the Menu button
8. Press right arrow button to “INSTALLATION” screen with “Antenna Setup” highlighted
9. Press OK button to enter the Antenna Setup screen
10. Press left arrow button to unchek AMC4 101.0W
11. Press Channel up button to highlight “IA5/Ku 97.0W”
12. Press OK button to highlight “LNB type”
13. Press right arrow button to display “Standard”
14. Press EXIT button and a window will pop up on the screen displaying “INFO – Press ok to save or EXIT”
15. Press OK button to save
16. Press EXIT button to enter the Installation Screen with Antenna Setup highlighted
17. Press arrow up button to highlight “Advanced Scan”
18. Press OK button and a window will pop up on the screen “FTA”
19. Press OK button to display the “Selected Satellite” window
20. Press OK button to enter the “ADVANCED SCAN” screen and “DOWN FREQUENCY” will be highlighted
21. Using the numeric keypad on the remote control enter the numbers 11842
22. Press down arrow button to “Symbol Rate”
23. With the number buttons on the remote control enter the numbers 22000
24. Press down arrow button to “Polarity” and press the right arrow button to display” Horizontal”
25. In the right hand side of the screen you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar (over 50%)
26. Verify green “Quality” bar to have highest strength of over 50%, press OK button to enter the “Channel Search” screen
27. When Channel Scan is completed, programming will automatically be displayed
28. Press Menu button, then right arrow button to go to Installation screen
29. Press arrow up or down button to highlight “Advanced Scan”
30. Press OK button and a prompt will appear Scan Mode “FTA”
31. Press OK button to display “Selected Satellite” window
32. Press OK button to enter the “ADVANCED SCAN” screen and “DOWN FREQUENCY” will be highlighted
33. Using the numeric keypad on the remote control enter the numbers 12060
34. Press down arrow button to “Symbol Rate”
35. With the numeric keypad on the remote control enter the numbers 22000
36. Press down arrow button to “Polarity” and press the right arrow button to display “Horizontal”
37. In the right hand side of the screen you will see two bars, one says “Level” and one says “Quality”. You should have a green “Level” bar over 50%. If not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel.
38. Verify green “Quality” bar to have highest strength of over 50%, press OK button to enter the “Channel Search” screen
39. When Channel Scan is completed, programming will automatically be displayed
Optional steps: If you would like to view all available free programming from this satellite (this will include secular and international programming) 
There are approximately 200 TV stations and 100 Radio stations on this satellite
40. Press the Menu button, then right arrow to enter Installation Screen
41. Press down arrow button to select Power Scan, press OK button
42. Press down arrow button to highlight Scan, the press OK
43. Power Scan window will appear and will list all available list all available services on the satellite. Do not interrupt, this process may take up to ten minutes to complete
44. The receiver will automatically go to viewing mode

Deleting Unwanted Channels
45. Press Menu button then right arrow button twice to enter Channel Edit menu with TV channel highlighted
46. Press Ok to enter Channel Edit – TV menu
47. Press down arrow to highlight delete, then press OK to select channels to delete
48. Use up or down arrow buttons to highlight channel to delete
49. Press right arrow button to mark unwanted channel with red line through text
50. Repeat steps 53 and 54 until all unwanted channels are selected
51. Press the OK button twice to delete unwanted channels
52. Press Exit button four times to view programming
[/toggle]

[toggle title=”GEOSATpro DVR1100c / DSR100c / DSR200c” variation=””]
GEOSATpro DVR1100c / DSR100c / DSR200c receivers automatically update from the satellite, and no manual channel programming is necessary.
If you are not receiving the new channels, or if the new channels are not automatically added to your receiver, verify that the Signal Quality (Q) reading on 3ABN (channel 106) is at least 50%, and that you are seeing television programming.

NOTE: Directional arrows on this remote control are:

Channel Up (Up Arrow)
Channel Down (Down Arrow)
Volume Up (Right Arrow)
Volume Down (Left Arrow).

To perform a Manual Update:
1 Using your GEOSATpro remote control, press Menu button
2 Left Arrow to Accessory Screen
3 Down Arrow to OTA
4 Press OK
5 Verify Automatic Update setting is ON (if it is OFF, press Right Arrow to ON)
6 Press Down Arrow to Update Now
7 Press OK
8 Screen displays” Do you want to update S/W?”
9 Press OK
10 After OTA update, the receiver will restart.
11 Press Menu button
12 Press VOL up button (the button that points to the right) three times to “UTILITY” menu
13 Press the Channel up button (the button that points to the up) to highlight “FACTORY DEFAULT”
14 Press OK button to display “ARE YOU SURE TO LOAD FACTORY DEFAULT?”
15 Press OK button to restart the receiver.
16 Press OK to select ENGLISH
17 Press OK to select GLORYSTAR
18 Press OK to select correct “TIMEZONE” then press OK
19 Press VOL up button to set “DAYLIGHT SAVINGS” ON or OFF
20 Press the Channel down button to highlight “NEXT”
21 Press OK button to display “CONNECT COAX CABLE” screen
22 Verify Signal Quality reading of at least 50% on 3ABN (channel 106) and on Cornerstone (channel 113)
23 Press orange Signal button to remove signal quality meter
24 The receiver date and time is automatically set by the satellite. Place the receiver on Channel 1 for at least 15 seconds to update

Note: Failure to have Signal Quality of at least 50% and displaying television programming on 3ABN (channel 106) will prevent the receiver from automatically updating and adding new channels.

GEOSATpro 1000ci
1. Using your GEOSATpro 1000ci remote control place the receiver on the 3ABN channel
2. Press “Menu” button
3. Press the Channel down button (the button that points down) to highlight “INSTALLATION”
4. Press OK button to go to “PASSWORD” screen
5. Using the numeric keypad on the remote control enter 0000
6. Press the Channel down button to highlight “TP EDIT / SCAN”
7. Press OK button to display the “TP EDIT / SCAN” screen
8. Verify that Satellite Name displays IA-5/Ku, if not, press right arrow button to display IA-5/Ku
9. Press the Channel down button to highlight “TP FREQUENCY”
10. Using the numeric keypad on the remote control enter 12060
11. If necessary, press Channel down button to highlight “POLARIZATION” and press right arrow button to display “Horizontal-18V”
12. Press Channel down to “SYMBOL RATE”
13. With the numeric keypad on the remote control enter the numbers 22000
14. Press Channel down button to highlight “Scan” and push the VOL up button until “FREE ONLY” is displayed
15. On the left side of the screen you will see a “SIGNAL QUALITY” strength indication bar. Verify signal quality is 50% or better, if not, you may need to fine-tune the dish and balance between the 11842 and the 12060 frequencies before scanning the new channel.
16. Press OK button to enter the “CHANNEL SCANNING” screen
17. When Channel Scan is completed, press exit four times to view programming
Deleting unwanted channels:
18. Press CH/LIST button on the remote control to enter TV Channel List screen
19. Use channel up or down button to select unwanted channels
20. Press the Blue Delete button on the remote control, prompt will request a password, Enter 0000
21. Press Ok to delete the channel
22. Select additional channel to delete and press Blue Delete button on the remote
23. Press Ok button to delete the channel
24. Repeat steps 22 and 23 until all unwanted channels are deleted
25. Press Exit button to view programming

Manhattan SKYLINE 1000
NOTE: Directional arrows on this remote control are:

Channel Up (Up Arrow)
Channel Down (Down Arrow)
Volume Up (Right Arrow)
Volume Down (Left Arrow).

1. Using your Manhattan SKYLINE 1000 remote control press the “MENU” button
2. Press the down arrow to highlight “Master Reset”
3. Press the OK button two (2) times and the screen will display “Resetting – Please Wait”
4. Press ESC button to exit “OSD SETUP”
5. Press ESC button to exit “TV SETTINGS”
6. Press ESC button to exit “TIME SETTINGS” (or enter time settings and select STORE and press OK)
7. Press ESC button to exit “ANTENNA SETTINGS”
8. Press down arrow to highlight “Search Mode”
9. Press left arrow to select “Auto FTA”
10. Press the channel down button to highlight “TP DATA”
11. Press OK button
12. A box will pop up to the right. At the top of that box, in yellow, make sure it says “TP1:3ABN”, if not, push the left or right arrow to get to “TP1:3ABN”
13. Press down arrow to “FREQ” (frequency)
14. Using the numerical keypad on the remote control enter the numbers 11842
15. Press down arrow to “Polarity”
16. Press left arrow to select “HORZ.”
17. Press down arrow to “S/R” (symbol rate)
18. Using the numerical keypad on the remote control enter the numbers 22000
19. Press down arrow to “FEC”
20. Press left arrow to select ¾
21. Press down arrow to “STORE”
22. Press OK button and screen will display “Storing Data – Please Wait”
23. Press OK button
24. A box will pop up to the right. At the top of that box, in yellow, make sure it says “TP2:ATN”, if not, push the left or right arrow to get to “TP2:ATN”
25. Press down arrow to “FREQ” (frequency)
26. Using the numerical keypad on the remote control enter the numbers 12060
27. Press down arrow to “Polarity”
28. Press left arrow to select “HORZ.”
29. Press down arrow to “S/R” (symbol rate)
30. Using the numerical keypad on the remote control enter the numbers 22000
31. Press down arrow to “FEC”
32. Press left arrow to select ¾
33. Press down arrow to “STORE”
34. Press OK button and screen will display “Storing Data – Please Wait”
35. Press Channel down button to “START”
36. Press OK button and upon channel scan completion the screen will display “Resetting – Please Wait”

To remove unwanted channels:
37. Press the “Menu” button
38. Press the right “VOL” arrow button to highlight “Edit” with “1 Channel Edit” yellow
39. Press the OK button, the screen will display “Channel Edit Menu”
40. Press the right “VOL” arrow button to change the function to “Delete”
41. Press the OK button to highlight a TV Channel yellow
42. Press the UP or DOWN “CH” button to highlight an unwanted channel to delete
43. Press the OK button two times, this will place a check mark beside the channel name
44. Press the UP or DOWN “CH” button to highlight additional unwanted channel to delete
45. Repeat steps 42 and 43 to select additional channels to delete
46. Press “ESC” button
47. Press “CH” down button to highlight “STORE”
48. Press the OK button to delete the selected channels
49. Prompt will display “STORING DATA, Please wait”
50. Press “ESC” button to view programming 


Manhattan DSR 1500
NOTE: Directional arrows on this remote control are:

Channel Up (Up Arrow)
Channel Down (Down Arrow)
Volume Up (Right Arrow)
Volume Down (Left Arrow).

1. Using your Manhattan DSR 1500 remote control press “SETUP” button (located above the #3 button)
2. Press down arrow and highlight “SYSTEM SETTING”
3. Press OK button
4. Press down arrow and highlight “DEFAULT SETTING”
5. Press OK button and the screen will display “WARNING: THIS WILL RESET ALL SETTINGS TO DEFAULT VALUES”
6. Press right arrow to select “OK”
7. Press OK button and the screen will display “WARNING: ARE YOU SURE YOU WANT TO CONTINUE”
8. Press right arrow to select “OK”
9. Press OK button
10. Screen will Display “PLEASE WAIT” then “STORED SETTINGS RESET TO DEFAULT”, press OK button to restart the receiver
11. Screen displays LANGUAGE SELECTION, press OK button
12. Press down arrow to “TP FREQUENCY”
13. Using the number buttons on the remote control enter the numbers 11842
14. Press down arrow to select POLARIZATION should be “HOR”
15. Press down arrow to ‘SYMBOL RATE”
16. Using the number buttons on the remote control enter the numbers 22000
17. If you have good level yellow/green bar on “Signal Strength”, press down arrow to “Start Search” (there will be quotation marks “” on either end of Start Search when it is selected)
18. Press the OK button
19. A box will pop up to the right. When you see the word “Store” at the bottom of that box press OK button
20. Screen will display “CHANNEL DATA IS BEING UPDATED” then return to a TV viewing screen
21. Press “SETUP” button
22. Press down arrow to highlight “Channel Search”
23. Press OK button to display the “Channel Search Menu”
24. Press down arrow to “TP FREQUENCY”
25. Using the numerical keypad on the remote control enter the numbers 12060
26. Press down arrow to select POLARIZATION should be “HOR”
27. Press down arrow to ‘SYMBOL RATE”
28. Using the number buttons on the remote control enter the numbers 22000
29. If the reading on “Signal Strength” meter is not at a strong and high level, you may need to fine-tune the dish to receive the new Channel
30. Press down arrow to “Start Search”
31. Press the OK button
32. A box will pop up to the right. When you see the word “Store” at the bottom of that box press OK button
33. Screen will display “CHANNEL DATA IS BEING UPDATED” then return to a TV viewing screen 

To remove unwanted channels:
34. Press “SETUP” button
35. Press down arrow to highlight “Edit Channel List”
36. Press OK to display “Edit Channel List” Menu
37. “Delete” will be selected by default
38. Press the OK button
39. Use down and right or left arrow buttons to select an unwanted channel
40. Press OK to delete the selected unwanted channel
41. Repeat steps 38–40 to delete all unwanted channels
42. Press down arrow to select “STORE”
43. Press OK to save changes
44. Press ESC button to view TV programming


Topfield 3000
NOTE: Directional arrows on this remote control are:

Channel Up (Up Arrow)
Channel Down (Down Arrow)
Volume Up (Right Arrow)
Volume Down (Left Arrow).

1. Using your Topfield 3000 remote control press the “MENU” button
2. Press down arrow to highlight “Installation”
3. Press OK button
4. Press down arrow to select “Factory Setting”
5. Press OK button to display “Reset All Data”
6. Press left arrow to select “Yes”
7. Press OK button to display “Position Data Delete”
8. Press left arrow to select “Yes”
9. Press OK button to continue
10. Press up arrow to select “SAT/TP Edit”
11. Press OK button again on “Satellite Name” (A window listing satellite names will pop-up on the right hand side)
12. Press down arrow to select “Telestar5(KU)” or “Intel_Amc5(KU)”
13. Press OK button
14. Press down arrow to select “Add new TP”
15. Press OK button to display new window “Add New TP – “Frequency” will be highlighted
16. Using the numerical keypad on the remote control enter the numbers 11842
17. Press down arrow to select “Symbol Rate”
18. With the numerical keypad on the remote control enter the numbers 22000
19. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal”
20. Press down arrow to the word “OK” and press the OK button on the remote control
21. “Add new TP” will be highlighted, Press “OK”
22. Using the numerical keypad on the remote control enter the numbers 12060
23. Press down arrow to select “Symbol Rate”
24. With the numerical keypad on the remote control enter the numbers 22000
25. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal”
26. Press down arrow to the word “OK” and press the OK button on the remote control
27. Press down arrow to select “Channel Search” and press the OK button on the remote control
28. Press Channel down button to select “Search Mode” and press the Volume up button (the button that points to the right) one time and it should display “Manual”
29. Press down arrow to select Frequency and press left arrow “VOL” button to select 11842 MHz
30. In the lower right hand corner you will see two signal indicator bars, “Level” and “Quality”. The “Level” reading should be green and the “Quality” reading should be 50% or better. If the “Quality” reading is low, fine tune the dish aiming before scanning for channels.
31. Press Channel down button to select “Start Search”
32. Press OK button and a “Searching” screen will appear
33. When Channel Scan is completed press OK, the Channel Search Screen will appear
34. Press Channel down arrow button to select “Search Mode” and press the Volume up button (the button that points to the right) and it should display “Manual”
35. Press down arrow to select Frequency and press right arrow “VOL” button to select 12060 MHz
36. Press Channel down button to select “Network Search” and press the Volume up button (the button that points to the right) one time and it should display “Off”.
37. Press Channel down button to select “Start Search”
38. Press OK button and a “Searching” screen will appear
39. When Channel Scan is completed press OK, the Channel Search Screen will appear
40. Press Exit button to exit the menus and view the new programming

To remove unwanted channels:
41. Press Channel up or down button to select “Organizing Channels”
42. Press the OK button to display “Organizing Channels” menu
43. Press Channel down button to highlight “Delete” Function
44. Press the OK button to enter the “Channel List”
45. Use the Channel up or down arrow button to highlight an unwanted channel
46. Press the OK button to select channel to be deleted, channel name will turn light gray
47. Press Channel up or down button to highlight an additional channel to delete
48. Press the OK button to select channel to be deleted. (Repeat steps 47 and 48 for additional channels)
49. Press Exit button, a prompt will appear “Delete services. Are you sure?”
50. Press left arrow to select Yes and press OK
51. Prompt will show “Deleting Services”, then will return to main “Main Menu” screen
52. Press exit to view programming


Topfield 4000 / 6200
NOTE: Directional arrows on this remote control are:

Channel Up (Up Arrow)
Channel Down (Down Arrow)
Volume Up (Right Arrow)
Volume Down (Left Arrow).

1. Using your Topfield 4000/6200 remote control press the “MENU” button
2. Press down arrow to highlight “Installation”
3. Press OK button
4. Press down arrow to select “Factory Setting”
5. Press OK button to display “Reset All Data”
6. Press left arrow to select “Yes”
7. Press OK button to display “Position Data Delete”
8. Press left arrow to select “Yes”
9. Press OK button to continue
10. Press up arrow to select “SAT/TP Edit”
11. Press OK button again on “Satellite Name” (A window listing satellite names will pop-up on the right hand side)
12. Press down arrow to select Intel_Amer5(KU)
13. Press OK button
14. Press down arrow to select “Add new TP”
15. Press OK button to display new window “Add New TP – “Frequency” will be highlighted
16. Using the numerical keypad on the remote control enter the numbers 11842
17. Press down arrow to select “Symbol Rate”
18. With the numerical keypad on the remote control enter the numbers 22000
19. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal”
20. Press down arrow to the word “OK” and press the OK button on the remote control
21. “Add new TP” will be highlighted, Press “OK”
22. Using the numerical keypad on the remote control enter the numbers 12060
23. Press down arrow to select “Symbol Rate”
24. With the numerical keypad on the remote control enter the numbers 22000
25. Press down arrow to select “Polarization” and push the right arrow one time and it should display “Horizontal”
26. Press down arrow to the word “OK” and press the OK button on the remote control
27. Press down arrow to select “Service Search” and press the OK button on the remote control
28. Press Channel down button to select “Search Mode” and press the Volume up button (the button that points to the right) one time and it should display “Manual”
29. Press down arrow to select Frequency and press left arrow “VOL” button to select 11842 MHz
30. In the lower right hand corner you will see two signal indicator bars, “Level” and “Quality”. The “Level” reading should be green and the “Quality” reading should be 50% or better. If the “Quality” reading is low, fine tune the dish aiming before scanning for channels.
31. Press Channel down button to select “Start Search”
32. Press OK button and a “Searching” screen will appear
33. When Channel Scan is completed press OK, the Channel Search Screen will appear
34. Press Channel down arrow button to select “Search Mode” and press the Volume up button (the button that points to the right) and it should display “Manual”
35. Press down arrow to select Frequency and press right arrow “VOL” button to select 12060 MHz
36. Press Channel down button to select “Network Search” and press the Volume up button (the button that points to the right) one time and it should display “Off”.
37. Press Channel down button to select “Start Search”
38. Press OK button and a “Searching” screen will appear
39. When Channel Scan is completed press OK, the Channel Search Screen will appear
40. Press Exit button to exit the menus and view the new programming

To remove unwanted channels:
41. Press Channel up or down button to select “Organizing Services”
42. Press the OK button to display “Organizing Channels” menu
43. Press Channel down button to highlight “Delete” Function
44. Press the OK button to enter the “Channel List”
45. Use the Channel up or down arrow button to highlight an unwanted channel
46. Press the OK button to select channel to be deleted, channel name will turn light gray
47. Press Channel up or down button to highlight an additional channel to delete
48. Press the OK button to select channel to be deleted. (Repeat steps 47 and 48 for additional channels)
49. Press Exit button, a prompt will appear “Delete services. Are you sure?”
50. Press left arrow to select Yes and press OK
51. Prompt will show “Deleting Services”, then will return to main “Main Menu” screen
52. Press exit to view programming